11.09.2017 Production of a high-temperature recuperator for reheating furnace of forging and pressing

31.08.2017 Manufacture and shipment of heat recovery of gas-turbine plant

24.08.2017 Production of air for preheating blocks for the vacuum distillation furnace of an oil refinery instead of the failed ones

23.08.2017 Production and shipment of a series of recuperators for a chemical plant

15.08.2017 Production and shipment of a flue gas cooler for a thermosetting unit

31.07.2017 Production and shipment of air heater to improve the efficiency of the fuel oil boiler

19.07.2017 Manufacture and shipment of a heat exchanger for heating water from flue gases of a boiler working on wood chips

07.07.2017 Manufacture and shipment of a series of heat exchangers for air cooling before intercooler diesel generator station

05.07.2017 Production of an experimental heat exchanger for cooling bulk materials, in this case sand-water

04.07.2017 Production and export of a compact heat exchanger to Lebanon for heating water from a diesel generator

03.07.2017 Manufacturing and shipping of a multi-pass recuperator to the painting chamber of a defense enterprise

29.06.2017 Manufacture and shipment of recuperator for chemical plant

27.06.2017 Production and shipment of low-temperature recuperator for Mongolia

27.06.2017 Production and shipment of multi-pass high-temperature recuperator for catalyst plant

23.06.2017 the Production and shipment of high temperature heat exchangers for a foreign customer

12.06.2017 The Production and shipment of two-section high-temperature recuperator for the largest metallurgical holding, Russia

27.05.2017 The Production and shipment of high-temperature recuperator for an low-power industrial furnace

27.05.2017 The Production and shipment of high-temperature heat exchanger for industrial furnace

17.05.2017 Installation and commissioning works on replacement of heat exchanger on the largest oil refinery far Eastern Federal district of the Russian Federation

12.05.2017 The Production and shipment of the heat exchanger with piping

06.05.2017 The Production and shipment of units of heat exchanger for refinery

15.04.2017 The Production and shipment of the units heat exchanger to replace the failed one

05.04.2017 The Production and shipment of a series of heat exchangers to cool the air before the intercooler of gas piston installation

20.03.2017 The Production and shipment of heat exchangers for the large capacity refinery furnace

05.03.2017 industrial heat exchanger for the air preheating the for related technological processes

21.02.2017 Production and shipment of air preheater for oil refinery

16.02.2017 Production and shipment of the heat exchanger (recuperator) for the largest metallurgical plant of Russia

15.02.2017 Production and shipment of a series of two air preheaters for industrial furnaces for oil refinery

20.01.2017 Production and shipment of the heat exchanger for forging furnaces

26.12.2016 Production and shipment of a series of heat exchangers for furnaces of continuous filament glass Chinese manufacturer

20.12.2016 Production and shipment of recuperator to the painting line of the manufacturer of building materials

17.12.2016 Production, testing of heat exchanger for heat treatment and shipment of heat exchangers for heating water

25.11.2016 Production and shipment of recuperator to the heating furnace of the spring workshop, the leader of the Russian market of spring for trucks

22.11.2016 Production and shipment of a high-temperature recuperator to an industrial low-power furnace

18.11.2016 Production and shipment sets of heat exchangers for drying materials and heat exchanger for water preheating.

17.11.2016 Production and pressure test and shipment of theheat exchanger with flue gas dilution system temperature up to °С

08.11.2016 Review the panels used in aggressive environments which we are using in the recuperators manufacturingmore.

08.11.2016 Production and testing of molding on a series of high-temperature heat exchangers for heating furnaces blacksmith shop.

07.11.2016 Production and shipment of the heat exchanger for the bell-factory.

03.11.2016 Production and shipment after the pressure tests the heat exchanger for heating enterprise shops.

28.10.2016 Production and shipment of high-temperature heat recovery section instead of the failed to the heating furnace with walking beams.

28.10.2016 Production and shipment of high-temperature heat exchanger for heating forging furnace largest metallurgical complex of Russia.

27.10.2016 Production and shipment of a series of heat exchangers for the drying of synthetic rubber.

16.10.2016 Production and shipment of high-temperature heat exchanger 8 sectioned high power for sheet-rolling shop of one of Russia's largest steel mills.

12.10.2016 Production and shipment of the air heater to the heating system of mines.

25.09.2016 Production and shipment of high-temperature heat exchanger для for plate rolling mill of metallurgical production.

16.09.2016 Signing of agreement with a leading engineering company in India for the supply of heat exchangers series, at the end of the exhibition in 2016 MMMM-EXPO more

09.09.2016 Production and shipment of the heat exchanger to install the compaction (granulation) of ammonium sulfate in the chemical industry.

18.08.2016 Company "Termo Nord Stream" participated in the largest industrial exhibition MMMM-EXPO 2016 in Delhi, India, which has become a platform for discussion of current and future projects with our existing and future customers.. more

15.08.2016 Production and shipment of the heat exchanger for heating water in the production of gypsum.

12.08.2016 Production and shipment of heat exchangers series for the largest soda manufacturer.

08.08.2016 Production and shipment of experimental heat exchanger for condensate collecting of gas mixture.

05.08.2016 Production and shipment of the heat exchanger for the largest Russian chemical holding.

03.07.2016 Production and shipment of heat exchangers series for machine-building enterprise of the Kazakhstan.

28.07.2016 Production and shipment of the heat exchanger for the production of chemical catalysts.

25.07.2016 Manufacturing, testing and shipment of heat exchangers series for machine-building in St. Petersburg.

21.07.2016 Control assembly, production and shipment of air heater for mining heating system.

15.07.2016 Production and shipment of the air heater unit for the refinery made under the project of replacing import equipment, which was dismantled due to being out of order.

30.06.2016 Production and shipment of the heat exchanger for heating after gas cleaning plants melting down of non-ferrous metals.

24.06.2016 Production and shipment of high capacity heat exchanger for air preheating of the Cardboard and Paper Mill.

08.06.2016 Production of high-power heat exchanger for heating the mine mining shaft and its control assembly before shipment.

19.05.2016 Manufacturing, testing and shipment of heat exchangers series for rotary furnaces of chemical production

10.05.2016 Manufacture, pressure testing and shipment of the the high temperature heat exchanger for the reheat furnace of the copper rolling shopfloor.

20.04.2016 Manufacture, pressure testing and shipment of the high temperature three-section heat exchanger for the leading Russian metallurgic enterprise.

30.03.2016 Manufacture, pressure testing and shipment of the heat exchanger series for room heating.

22.03.2016 Shipment of the high power high temperature six-section heat exchanger for the second stage of the heat recovery systems retooling and modernization program for the flat rolled products manufacturing in one of the largest Russian metallurgic integrated plants.

10.03.2016 Inspection of the high temperature heat exchanger 6 months of continuous operation in the metallurgic plant

04.03.2016 Our company is in tune with the times, we are open for our colleagues and customers. Now you can look to our life in Instagram.

01.03.2016 We are launching our new site to be even more convenient for you. The old version of the site is available in archives .

25.02.2016 Manufacture and shipment of the high temperature heat exchanger for the largest machine engineering plant in Sankt-Petersburg.

19.02.2016 Installation and successful commissioning of the high power high temperature six-section heat exchanger for the first stage of the heat recovery systems retooling and modernization program for the flat rolled products manufacturing in one of the largest Russian metallurgic integrated plants.

15.02.2016 Manufacture and shipment of the high temperature heat exchanger series the machine engineering enterprise.

20.01.2016 Manufacture, pressure testing and shipment of the high temperature heat exchanger for the largest Russian metallurgic holding company.

30.12.2015 Manufacture and shipment of the high temperature heat exchanger for chemical industry.

25.12.2015 Manufacture, pressure testing and shipment of the first stage of the heat exchanger series .

17.12.2015 Manufacture and shipment of the high power high temperature six-section heat exchanger for the first stage of the heat recovery systems retooling and modernization program for the flat rolled products manufacturing in one of the largest Russian metallurgic integrated plants.

02.12.2015 Manufacture, fit-up assembly test, pressure testing and shipment of the heat exchanger for the zinc melting furnace of the largest non-ferrous metal producer in RK.

20.11.2015 Manufacture, pressure testing and shipment of the high temperature heat exchanger for metallurgic industry.

30.10.2015 Manufacture, pressure testing, packing and shipment of the four heat exchanger series for the largest Russian soda producer.

25.10.2015 Manufacture and shipment of the heat exchanger for the coal mine heating system.

07.10.2015 Inspection of the high temperature heat exchanger after 6 months of continuous operation

02.10.2015 New video on our site:
Fit up assembly test of the heat exchanger for the coal mine heating system

28.09.2015 Manufacture and pressure testing of the air heating heat exchanger for shopfloor heating.

04.09.2015 Manufacture, pressure testing, packing and shipment of the high temperature three-section heat exchanger for the leading Russian metallurgic enterprise.

30.07.2015 Manufacture and pressure testing of the heat exchanger for small volumes of flue gases.

20.07.2015 Termo Nord Stream took part in the largest industrial exhibition “Innoprom-2015” which became a ground for discussion about the implemented, current and future projects with our current and future customers.

16.07.2015 Manufacture, pressure testing and shipment of the heat exchanger for construction materials production.

10.07.2015 Fit up assembly and shipment of the heat exchanger for the long product rolling mill of the oldest Russian ironworks. High complexity of the heat exchanger design is stipulated by the rigid framework of the technical requirements for manufacture.

01.07.2015 Manufacture, pressure testing and shipment of the heat exchanger series for soda-ash roasting furnaces.

23.06.2015 Manufacture of the flue gas wasteheat exchanger for green houses supply.

28.05.2015 Pressure testing and shipment of two heat exchanger series to increase the boiler efficiency and decrease the flue gas temperature before the exhauster..

13.05.2015 Pressure testing and shipment after manufacture and assembly of the high-temperature heat exchanger series .

05.05.2015 Manufacture, pressure testing and shipment of the heat exchanger for room heating.

24.04.2015 Packing and marking of our production at shipment to the customer.

16.04.2015 Another attempt to capture our intellectual property is suppressed. By the decision of Russian Federal Agency for Intellectual Property, Patents and Trademarks dated March 30, 2015 the utility model for the panel high-frequency welding line No. 132021 was considered as a piracy to the full extent and was withdrawn, all its useful characteristics are known from our patent and technical literature.

06.04.2015 Manufacture, pressure testing and shipment of the high temperature heat exchanger

01.04.2015 Welcome to the new site of Termo Nord Stream.
We hasten to let you know that we have launched a new site which covers much more vividly our technological capabilities and operational experience.

30.03.2015 Termo Nord Stream management represented by the General Director participated actively in the conference Metallurgy-Intecheco “Metallurgy renewal”, innovative technologies and ecology.

19.03.2015 Manufacture and pressure testing of the heat exchanger series for blast preheating of the gasoline tube hipped preheater burners before distillation for Lukoil OJSC needs.

18.02.2015 Termo Nord Stream Ltd patented the utility model for the gas-liquid exchangers design with priority dated 11.07.2014 The patent protests the copyright law of Termo Nord Stream for production of the new TOR type high-performance heat exchangers range.

12.03.2015 Termo Nord Stream management represented by the General Director visited Chysovoy metallurgic plant.
In order to inspect the heat exchanger working for 15 years in 800 mill continuous furnace. This is the first OPT type serial plate heat exchanger made by Termo Nord Stream.

10.03.2015 Manufacture, fit up assembly test, pressure testing and shipment of the heat exchanger with the operating temperature of 700oС

02.03.2015 Fit up assembly test and leakage test of the high power heat exchanger for the largest Russian oil refinery.

26.02.2015 We completed the heat exchanger manufactory within the scope of the import substitution activity (Belgium equipment) for Rosneft OJSC needs.

18.02.2015 Termo Nord Stream Ltd patented the utility model for the gas-liquid exchangers design with priority dated 11.07.2014 The patent protests the copyright law of Termo Nord Stream for production of the new TOR type high-performance heat exchangers range.

17.02.2015 Shipment of ТОR-600/3.0 90/0.36 feed water heater for the pyrolysis plant

12.02.2015 We launch the new production line of the high performance industrial heat exchangers for liquid heating.

27.01.2015 Termo Nord Stream has won the tender for delivery of the heat exchanger series for Lukoil OJSC needs.

15.01.2015 The new equipment package system is implemented to provide safety of our production during transportation

26.12.2014 We have finished shipment of the heat exchanger to 5000 Mill for the leader of the Russian metallurgic industry

24.12.2014 We have completed manufactory and shipment of the high temperature heat exchanger series

15.12.2014 Shipment of the high power heat exchangers for chemical plant

05.12.2014 Inspection of the heat exchanger at Pobuzhye Ferronickel Integrated Plant after 2 years of operation (1 year using powdered coal fuel), dust content up to 100 g/m3

02.12.2014 Within the framework of the import substitution program Termo Nord Stream has entered into the contract for delivery of the high power heat exchanger for Rosneft OJSC needs.

24.11.2014 Inspection of the heat exchanger manufactured by Termo Nord Stream
This heat exchanger is installed at the ferronickel production and operates at the temperature of 600-800 С with sulfur-containing flue gases with dust content up to 150 g/m3. Inspection was performed after 6 months of the heat exchanger operation.

12.11.2014 Termo Nord Stream starts implementation of the import substitution program. Our production is not only highly competitive with the items from around the world, but also significantly exceeds the best world’s equipment in a number of technological and especially economical characteristics

13.10.2014 WE INVITE YOU TO THE INTERNATIONAL RESEARCH-TO-PRACTICE CONFERENCE “ENERGY-SAVING TECHNOLOGIES IN INDUSTRY. FURNACE UNITS. ECOLOGY” Our report « INDUSTRIAL HEAT EXCHANGERS APPLICATION » will take place at 12.20, October 16, 2014 (lec. hall. B-3) Moscow, V-49, Leninskiy av. 4, MISaA NRTU, EMC

30.09.2014 WE INVITE YOU TO THE VITH INTERNATIONAL SPECIALIZED EXHIBITION “ENERGY SAVING AND ENERGY EFFICIENCY. INNOVATIVE TECHNOLOGIES AND EQUIPMENT" from October 7 to October 10! We will glad to see all visitors. Sankt-Petersburg, Peterburgskoye shosse, 64/1, Expoforum CEC, 2 hall

17.09.2014

Attention!
Defective counterfeits copying ОПТтм heat exchangers design appear at the heat exchangers market under different names and abbreviations, its design uses ribbed panels manufactured by standard welding methods, generally using welding by semi-automated machines. At this welding method the seam of stainless steel thin-walled blank parts gets crusty and cracks. Purchasing the ribbed plate heat exchangers ask to demonstrate the process of the panel high-frequency welding; ask for pressure testing of the item.



12.09.2014 We have completed manufacture and shipment of the high temperature heat exchanger series

02.09.2014 Shipment of two sections of the fourth stage of the high power industrial heat exchanger

30.08.2014 Installation and commissioning works for the heat exchanger for ferronickel plant

27.07.2014 We have completed manufacture of the industrial heat exchanger series for heat recovery into the production process

17.07.2014 We have developed OPT-therm program provided for heat and hydraulic calculations of OPT ribbed plate heat exchangers.

26.06.2014 Shipment of two sections of the third stage of the high power industrial heat exchanger

03.06.2014 We have completed shipment of the second stage of the three-section heat exchanger for ferronickel plant

29.05.2014 Отгрузка четырех рекуператоров для химического производства
Отгрузка четырех промышленных рекуператоров рекуператоров для химического производства.

29.04.2014 Shipment of four heat exchangers for chemical plant Shipment of four industrial heat exchangers for chemical plant.

20.04.2014 Shipment of three-section heat exchanger Shipment of the three-section heat exchanger for ferronickel production.

31.03.2014 Shipment of the high power heat exchanger for gaseous dusty mediums We offer you photo and video report about shipment of high power heat exchanger for the customer in Guatemala.

11.03.2014 Research department of Termo Nord Stream has been designated into the separate division to investigate issues concerning increase of OPT type heat exchanger quality and effectiveness, and improvement of production processes at heat exchangers manufacture. In section «Research work» you may learn about the first results of the division.

25.02.2014 Commissioning of the second stage of ribbed panels production; along with the complete production cycle of the heat exchangers which was commissioned earlier it allows to increase threefold heat exchanger equipment production

24.01.2014 We have obtained favorable decision for the patent protecting the ribbed panel heat exchanger design.

02.12.2013 Dear colleagues! We provide additional 6-month warranty for every person entering into the contract till 31.12.2013 Thus, the total warranty period will be 30 months!

25.11.2013 Results of "Metal Expo 2013” exhibition: According to the exhibition results the contracts of intent were prepared for entering into with a number of enterprises in different branches of industry.

20.11.2013 Shipment of the next heat exchanger batch for BSK OJSC

18.11.2013 Our company proceeds to calculation and design of the high-duty heat exchangers for the nuclear industry

14.11.2013 Произведена отгрузка теплообменного оборудования для ЗАО "ПО "РежНикель"

09.11.2013 We invite to visit our 1G09 stand at "Metal Expo 2013" exhibition from November 12 to November 15! We will glad to see all visitors.

27.09.2013 Reliability of the heat exchangers manufactured by Termo Nord Stream. We inspected the heat exchanger after 10 months of operation in the severe dusty conditions (abrasive constituent up to 100 g/Nm3) at Pobuzhye Ferronickel Integrated Plant. Visual estimate didn’t reveal any wear of the heat exchanger working surfaces. Adhering and slagging on the surfaces of gas ducts and heat exchangers was fully absent.

02.09.2013 Entering into the contract for manufacture of industrial heat exchanger batch for Guatemala.

24.08.2013 Increase of heat exchangers industrial output. We completed manufacture of the ribbing line for the second production stage which allows to increase 2-3 times heat exchangers industrial output

 





Our equipment is used by: